 Assured the integrities of equipment:  No Mechanical damage due to process to the equipment.  To check welding condition external and internal.  To witness Hydro or Pneumatic Testing, Welding Repair.  To liaise with NDT team for Inspection required.  Witnesses bolt torqueing and bolt tensioning of the flanges and verify proper alignment thereof.  Ensured:  Plates, Pipes, Flanges, Structure Materials, Fittings and Valves, Gaskets, bolts & nuts materials are receive -inspected as per the Inspection and Test Plan.  Dimensional stability to Materials spec, heat numbers, mechanical properties to drawing and material test certificate.  Edge preparations are carried out and the bevel is clean and the bevel angle is checked prior to fit-up as per QCP.  No excess miss-alignment is allowed and the root gap and the geometrical parameters are ensured as per code and WPS.  Sub-assembly and final dimensional inspection to the approved drawing.  Electrodes/filler wires and other consumables are as per WPS Pre-heating if any.  Administered:  Root welding & final welding visual inspection, NDE if required.  Checking of the inter pass temperature & recording the parameters as per WPS.  Welding inspection. (Surveillance checks before, during and after welding).  Ensure that all NDT specified are carried out and the reports are reviewed.  Interpretation of radiographic films and repair/NDT activities if needed.  Monitoring PWHT operation, review charts and reports.  Ensuring hardness after PWHT to confirm the adequacy of PWHT and do RT & MT if specified.  Pre- commissioning activities are met as hydro test, thickness check etc.  Witness hydro test and review the charts and reports.  Non confirming products are identified/rectified and re-checked.  Assured:  Ensuring the inspection and fabrication of Tank before releasing it for hydro test.

 Preparation of Inspection Test Plan.  Preparation of welding procedure specification as per the project requirement and code.  Qualifying a PQR according to the code requirement.  Plates, Pipes, Flanges, Structure Materials, Fittings and Valves, Gaskets, bolts & nuts materials are receive -inspected as per the Inspection and Test Plan.  Dimensional stability to Materials spec, heat numbers, mechanical properties to drawing and material test certificate.  Edge preparations are carried out and the bevel is clean and the bevel angle is checked prior to fit-up as per QCP.  No excess miss-alignment is allowed and the root gap and the geometrical parameters are ensured as per code and WPS.  Sub-assembly and final dimensional inspection to the approved drawing.  Electrodes/filler wires and other consumables are as per WPS Pre-heating if any.  Administered:  Root welding & final welding visual inspection, NDE if required.  Checking of the inter pass temperature & recording the parameters as per WPS.  Welding inspection. (Surveillance checks before, during and after welding).  Ensure that all NDT specified are carried out and the reports are reviewed.  Interpretation of radiographic films and repair/NDT activities if needed.  Monitoring PWHT operation, review charts and reports.  Ensuring hardness after PWHT to confirm the adequacy of PWHT and do RT & MT if specified.  Pre- commissioning activities are met as hydro test, thickness check etc.  Witness hydro test and review the charts and reports.  Non confirming products are identified/rectified and re-checked.  Assured:  NDT is fully carried out/accepted to piping spools prior to its erection.  Field weld radiography is carried out at planned time so that project progress is not affected.

 Managed Turbine, Condenser, Low Pressure heaters Quality Control.  To check, inspect and test incoming welding and construction materials to ensure that they meet project specification requirement as per section ASME Sec 2.  To check the handling procedure of welding consumables as per section ASME Sec II c, like Baking, Re baking, Holding and Re-conditioning.  To follow the inspection procedures as per the activity mentioned in the ITP.  Dimensional check to drawing requirement  To inspect Turbine Casing UT Check, DP Check, Leak Test.  Surface magnetic particle inspections  Material identification using portable instrumentation  Ultrasonic inspection of blade fixings, blade roots, erosion shields and other features.  Hydrostatic Testing of, Turbine Casings, Main Stop Valves.  Overspeed and Dynamic Balancing Test of Turbine rotors.  Radial Clearance between turbine and Casings,  Axial Clearance between Rotor Blades and stationary points.  Hydrostatic Test of Condenser, LP Heater.  Kerosene Oil Leak Test for Oil Trough, Condenser.  Pneumatic Test of LP Heater tube bundles and its shell.  NDT Review of LP heaters and Condenser.